PERANCANGAN KONSEPTUAL LIGHTWEIGHT PULLEY BERBAHAN ALUMINIUM 6061-T6

Authors

  • Fajar Maulana Universitas Lancang Kuning, Indonesia Author
  • Bintha Ustafiano Universitas Lancang Kuning, Indonesia Author
  • Yolana Nursyafti Universitas Lancang Kuning, Indonesia Author

DOI:

https://doi.org/10.54314/jv7x3m96

Keywords:

lightweight pulley, desain CAD, aluminium 6061-T6, optimasi geometri, sistem pemindah tenaga

Abstract

Abstract: This study aimed to develop a conceptual lightweight pulley design as an alternative approach to reducing component mass in a vehicle power-transmission system. The development used a computer-aided design (CAD) approach and considered pulley function, belt-system compatibility, geometric optimization, and manufacturability. The design concept used 6061-T6 aluminum alloy and incorporated lightening holes in the pulley disc. The design reference was a 2015 Toyota Yaris. The initial specifications included an outer diameter of 138 mm, a central bore of 30 mm, a hub diameter of 52 mm, a total thickness of 32 mm, a belt-contact width of 24 mm, and six belt ribs. The mass-reduction configuration consisted of six 30 mm-diameter holes and two 8 mm-diameter holes. The current output was a conceptual design and preliminary technical specification for subsequent development. The initial review indicated that the hub and belt-groove areas were retained, while modifications were concentrated on the disc section to reduce material use. However, this study has not yet produced quantitative mass-reduction data, CAE simulation results, a physical prototype, or vehicle performance test results. Therefore, the effects of the proposed design on structural strength and vehicle performance still need to be verified through simulation, manufacturing, dimensional inspection, and experimental testing.

Keywords: lightweight pulley, CAD design, 6061-T6 aluminum, geometric optimization, power transmission

 

Abstrak: Penelitian ini bertujuan mengembangkan desain konseptual lightweight pulley sebagai alternatif pengurangan massa komponen pada sistem pemindah tenaga kendaraan. Pengembangan dilakukan dengan pendekatan perancangan berbantuan komputer (Computer-Aided Design/CAD), dengan mempertimbangkan fungsi pulley, kompatibilitas terhadap sistem belt, optimasi geometri, serta kemungkinan proses manufaktur. Konsep desain menggunakan aluminium alloy 6061-T6 dan menerapkan lubang reduksi massa (lightening hole) pada bagian cakram pulley. Produk dirancang dengan referensi kendaraan Toyota Yaris tahun 2015. Spesifikasi awal meliputi diameter luar 138 mm, bore tengah 30 mm, diameter hub 52 mm, ketebalan total 32 mm, lebar area belt 24 mm, dan enam rib groove. Konfigurasi reduksi massa terdiri atas enam lubang berdiameter 30 mm dan dua lubang berdiameter 8 mm. Hasil tahap ini berupa desain konseptual dan spesifikasi teknis awal yang dapat digunakan sebagai dasar pengembangan selanjutnya. Evaluasi awal menunjukkan bahwa area hub dan groove tetap dipertahankan dalam rancangan, sementara modifikasi dilakukan pada bagian cakram untuk mengurangi penggunaan material. Namun, penelitian ini belum menghasilkan data kuantitatif pengurangan massa, hasil simulasi CAE, prototipe fisik, maupun pengujian performa kendaraan. Oleh sebab itu, pengaruh desain terhadap kekuatan struktur dan performa masih perlu diverifikasi melalui simulasi, manufaktur, inspeksi dimensi, dan pengujian eksperimental.

Kata kunci: lightweight pulley, desain CAD, aluminium 6061-T6, optimasi geometri, sistem pemindah tenaga

Downloads

Download data is not yet available.

References

Badan Pusat Statistik. (2023). Statistik transportasi Indonesia. BPS.

Kumar, R., & Gupta, S. (2021). Lightweight materials in automotive engineering for fuel efficiency improvement. Automotive Science Journal, 12(3), 200–210. https://doi.org/10.1016/j.asj.2021.03.010

Setiawan, M. Y. (2025). Pengaruh massa komponen CVT terhadap konsumsi bahan bakar sepeda motor. Jurnal Teknik Otomotif, 10(1), 15–22.

Smith, J., & Brown, A. (2022). Analysis of continuously variable transmission systems for vehicle efficiency. Journal of Mechanical Engineering, 45(2), 120–128. https://doi.org/10.1016/j.jme.2022.02.005

Winoko, Y. A. (2024). Analisis variasi CVT terhadap performa mesin sepeda motor. Jurnal Teknologi Kendaraan, 8(2), 45–53.

Downloads

Published

2026-10-31

How to Cite

PERANCANGAN KONSEPTUAL LIGHTWEIGHT PULLEY BERBAHAN ALUMINIUM 6061-T6. (2026). JOURNAL OF SCIENCE AND SOCIAL RESEARCH, 9(5), 9431 – 9434. https://doi.org/10.54314/jv7x3m96